AMS 5502
Descriptions AMS 5502 datasheet, AMS 5502 Chemical, AMS 5502 Properties from Steelmaking, Blooming, Hot forging, Hot rolling, Heat treatment, Straightening, 100% Ultrasonic flaw detection test, Cold working or Machined. All of these materials conform to M
| Product parameters | |
| Material Category:: | Stainless Steel |
| Steel Grade: | AMS 5502 |
| Material Technical Standards:: | AMS |
| Place of Origin: | USA |
Description
TECHNICAL SPECIFICATIONS - AFNOR 35NCDV12
MATERIAL FORM: Bar, Sheet, Strip
MATERIAL TYPE: Aerospace Material Specification - Structural steel
Official Test Certificate Report: issued by TUV - SGS - BV
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.30 ~ 0.40
Mn (%): 0.40 ~ 0.70
Si (%): ≤ 0.35
P (%))≤: 0.015
S (%))≤: 0.015
Cr (％): 1.00 ~ 1.40
Ni (％): 2.50 ~ 3.50
Mo (％): 0.35 ~ 0.60
Others (％): V 0.08 ~ 0.20, Al ≤: 0.015
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Tensile strength, σb/≥MPa: 1100
Yield strength, σ0.2/≥MPa: 850
Elongation, δ (％)≥: 8.0
Reduction of area, ф (％)≥: -
Anneal hardness ≤(HBW): 240
PRODUCT DESCRIPTION
The alloy is usually produced by VM / CVM followed by electroslag refining (ESR), Vacuum Arc Melting (VAR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' specific requirements.
Round bar / Wire rod (Diameter) 0.10mm to 300mm
Square bar / Flat bar: 3mm to 400mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 400mm X W100 - 1000mm X L1000 - 6000mm
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE & SERVICE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineer. E-mail: sales@cnlhss.com.
MATERIAL FORM: Bar, Sheet, Strip
MATERIAL TYPE: Aerospace Material Specification - Structural steel
Official Test Certificate Report: issued by TUV - SGS - BV
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.30 ~ 0.40
Mn (%): 0.40 ~ 0.70
Si (%): ≤ 0.35
P (%))≤: 0.015
S (%))≤: 0.015
Cr (％): 1.00 ~ 1.40
Ni (％): 2.50 ~ 3.50
Mo (％): 0.35 ~ 0.60
Others (％): V 0.08 ~ 0.20, Al ≤: 0.015
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Tensile strength, σb/≥MPa: 1100
Yield strength, σ0.2/≥MPa: 850
Elongation, δ (％)≥: 8.0
Reduction of area, ф (％)≥: -
Anneal hardness ≤(HBW): 240
PRODUCT DESCRIPTION
The alloy is usually produced by VM / CVM followed by electroslag refining (ESR), Vacuum Arc Melting (VAR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' specific requirements.
Round bar / Wire rod (Diameter) 0.10mm to 300mm
Square bar / Flat bar: 3mm to 400mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T60 - 400mm X W100 - 1000mm X L1000 - 6000mm
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE & SERVICE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineer. E-mail: sales@cnlhss.com.
